skid resistant coating > suspension bridge main cable wear skid resistant coating

suspension bridge main cable wear skid resistant coating

BD70 suspension bridge main cable anti abrasion wear skid resistant repair epoxy coating

Packaging specification of BD70 main cable of suspension bridge repair wearing compound skid resistant coatings:
Two-component,10Kg/group,packed in a plastic drum,A component:8.33Kg/drum,B component: 1.67Kg/drum.
We could offer professional customized packaging and sub-package services based on users' requirements

Performance features of BD70 suspension bride main cable wearing abrasion skid resistant epoxy compound
repair coating:
1.Two components room temperature curing macro-molecule coating
2.With fast curing speed and high bonding strength,the cured products have a good wear resistance and low temperature resistance
3.The bonding scope is wide,with a good adhesion to rubber,leather,metal and cement etc.
4.The coating has a high cohesion strength,with a good aging resistance and fire resistance.
5.With a good manufacture-ability,convenient for using

Product usage：
Mainly used in the mat formation of side walk skid resistant coating indoor and outdoor.Especially used in the preparation of
suspension bridge main cable anti skid abrasion wear resistant coating

How to use：
1.Put the adhesive tape paste into the around of pending-construction part,in order to protecting the non-needing construction part from
polluting by the coating.

2.Clean the pending-bonding surface,clean up the oil stains,dust and other impurities with toluene or xylene,then dry it.

3.According to the mass ratio A:B=5:1,make the B pour into the A,it can be used after mixing and stirring uniformly,the usable time
is 15 min.This anti skid resistant coating can do brush coating or roller coating,brush coating for 2 times,the interval for each time
brush coating is 0.5 to 1 hour.15 min later after the second brush coating,sprinkle a thin layer of abrasive particles,then brush the topcoat
once again,room temperature curing for 24 hours.The curing time should prolong for 48 hours under the temperature of 0～10 degree.

4.Configure the topcoat according to the below ratio: this product(BD70 skid resistant coating) : acetic ester=1:3,stir it uniformly.

5.Remove the paste adhesive tape and finish the construction.

physical index：

BD70 bridge metal cable anti abrasion skid resistant coating data performance table
-	Appearance（visual inspection）	Viscosity（Pa·s，25℃） GB/T2794-1995	Density (20℃ g/cm3 ) GB1033-1986	Surface drying Time（min）GB/7123-1986	weathering resistance(UV irradiation for 7 days) GB/T1766-1992	Working temperature(℃)	Shore A HardnessGB/10807-1989
-	Uniform viscous liquid, without impurities	2.0±0.6	1.18	30～50	without changing	-60～90	60

BD70 anti skid wear abrasion resistant coating performance table
Tensile strength MPa GB/T1040-1992	Elongation ％ GB528	Tearing strength kN/m GB 529	Peeling strength（N/2.5cm） GB/T2791-1995	-
29.1	520	23.4	136.6	-

Notes:
1.Make the main agent A and curing agent B weigh according to the specified proportion,make sure it mix and stir uniformly.
2.Please use it in time after configuring adhesives,in order to avoid causing waste based on the adhesive changing thick.
3.acetic ether is the diluting agent of this product
4.The coating without curing is afraid of water,try your best to avoid outdoor construction in the rainy day
5.Forbid walking on the skid resistant coating without complete curing

Storage：
This product is general chemicals,in the process of transportation and storage,should pay attention to water proof and fire prevention,
stored in a cool and dry place,the storage period is 12 months.

Construction protective measures：
1.Wear the protective masks,wear the protective glasses and rubber gloves
2.Need washing hands with soap before eating,drinking or smoking.
3.The health hazard after touching: a few people will have skin allergy phenomenon,see a doctor in time and avoid touching with
this product again.should wipe it with ethyl acetate when the sizing material paste on the skin by careless,then wash it with clear water.
Should wash it with clear water immediately and see a doctor when splashing into the eyes by careless.

Warm Prompt：
Residual adhesive solution cured products are non-toxic harmless organic solid,but maybe it will produce poisonous gas
when burning,non-professional personnel can not do combustion disposal,should be sent to garbage power plant or garbage burning
place treatment.

fire prevention measures：
Should choose dry powder to extinguish fire when toluene, xylene, ethyl acetate catching fire,can cover and flap it with dry powder,
grit(the construction using abrasive) or the non chemical fiber fabric when the sizing material catching fire.

Construction case photo shows:

------分隔线----------------------------